|
|
Home – Home – Jornals – Combustion, Explosion and Shock Waves 2026 number 6
2026 year, number 6
|
R. M. Fedorenko, V. M. Chobotova, P. A. Strizhak
Tomsk Polytechnic University, Tomsk, Russia
Keywords: water-fuel emulsions, emulsified fuels, microexplosive fragmentation, combustion mechanisms and modes, kinetic characteristics
Abstract >>
This article analyzes current understanding of the influence of water on the physicochemical properties and thermal conversion characteristics of water-fuel emulsions, taking into account successive stages-from their preparation to the oxidation of the air-fuel mixture formed during their evaporation. The kinetics of microexplosive fragmentation of emulsified fuel droplets and its influence on their combustion dynamics are studied. An analysis of the kinetic principles of thermal conversion is conducted, including ignition characteristics, changes in flame structure, combustion mechanisms, and combustion modes. The conditions for the initiation and characteristics of detonation combustion of water-fuel emulsions are analyzed. Rational combustion conditions ensuring reduced emission characteristics are determined. Using multicriteria analysis, the multidirectional influence of water on the properties, limiting conditions for initiation, and combustion characteristics of emulsified fuels is substantiated.
|
|
D. A. Slastnaya1, V. V. Lukashov1, V. A. Fedorenko1, R. I. Mullyadzhanov1,2, V. M. Dulin1,2
1Kutateladze Institute of Thermal Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia 2Novosibirsk State University, Novosibirsk, Russia
Keywords: ammonia-hydrogen-air mixture, laminar premixed flame, direct numerical simulation, detailed chemical-kinetic mechanism, laminarSMOKE, OpenFOAM
Abstract >>
The article presents the results of an experimental and numerical study of a laminar jet flame of a premixed NH3/H2/air mixture with an excess fuel ratio of 1.22 and a hydrogen volume fraction in the fuel of 30%. Three detailed chemical-kinetic mechanisms and their ability to predict flame temperature and shape, as well as the composition of combustion products, are compared. The results show that all used kinetic mechanisms predict similar flame temperature distributions and flame front location. The H2 and O2 distributions demonstrate satisfactory agreement with experiment. Local maxima in the OH distribution allow the position of the inner and outer flame fronts to be unambiguously determined. The NO concentration maximum for the three kinetic mechanisms is located in the inner flame front. The NO distribution values closest to the experimental data are observed in the outer region of the flame.
|
|
A. N. Dubovitsky1, E. D. Sverdlov1, V. D. Kobtsev1, D. N. Kozlov1,2, S. A. Kostritsa1, S. N. Orlov1,2, V. V. Smirnov1,2, V. I. Fabelinsky2
1Baranov Central Institute of Aviation Motors, Moscow, Russia 2Prokhorov Institute of General Physics, Russian Academy of Sciences, Moscow, Russia
Keywords: optical methods, chemiluminescence of OH* radicals, low-emission technology for combustion of hydrogen-air mixtures, surface and volume turbulent combustion, multi-pylon front combustion chamber device, NO emission
Abstract >>
By recording and analyzing chemiluminescence images of electronically excited OH* radicals in the UV spectral region (near 310 nm), we studied the combustion of hydrogen injected into a coflow airflow downstream of a multi-pylon front-end design of a low-emission combustion chamber. Experiments were conducted with variations in the turbulence scale and the pulsating component of the airflow velocity, which determine the volumetric or surface nature (mechanism) of turbulent combustion. The resulting images provide qualitative and quantitative information on both volumetric turbulent combustion (blurred OH* radical concentration fields with peaks in the axial zone of the fuel jets and relatively high concentrations at the mixing boundaries of the hydrogen jets with air) and surface turbulent combustion (pronounced narrow regions of OH* radicals at the mixing boundaries of the fuel with air and their absence in the axial zone of the fuel jets).
|
|
Y.-C. Zhao1,2, Y.-B. Li1, A. A. Mohamed1, Z. Miao1, D.-H. Ai3, Q.-F. Wang4
1Navigation College, Dalian Maritime University, Dalian, China 2Dalian Key Laboratory of Safety & Security Technology for Autonomous Shipping, Dalian, China 3School of Construction Engineering, Shenzhen Polytechnic University, Shenzhen, China 4School of Mechanical-Electronic and Vehicle Engineering, Beijing University of Civil, Beijing, China
Keywords: XiFoam, lithium-ion battery, gas leakage and diffusion, explosion impact, more ignition points
Abstract >>
This study investigates fire and explosion hazards in lithium-ion battery ships using numerical simulations with the XiFoam solver in the OpenFOAM platform. The research focuses on the leakage and explosion of thermal runaway gases in the engine room of a hybrid energy vessel. Simulations show that obstructions significantly alter gas dispersion, causing high-concentration gas clouds to accumulate in specific compartments, especially near battery units. The analysis covers pressure distribution, shock wave propagation, and the effects of single versus multiple ignition sources. Results show that maximum explosion overpressure occurs in high-concentration gas regions, where rapid gas expansion creates a negative pressure zone. The pressure wave impinges on the bulkhead, reflects, and propagates semicircularly through passages into adjacent compartments. Higher gas concentrations result in greater explosion overpressure, with peak values observed near the batteries. Additionally, simulations with multiple ignition points were conducted. When ignition points are widely spaced, multiple annular low-pressure zones form. Closely spaced ignition points cause the low-pressure zones to merge into a single annular band. Under delayed multi-point ignition, a high-pressure zone forms between ignition points, significantly increasing local destructive effects.
|
|
A. A. Vasilyev1,2, V. A. Vasilyev1, T. V. Vasilyev3
1Lavrentyev Institute of Hydrodynamics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia 2Kutateladze Institute of Thermal Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia 3Novosibirsk State University, Novosibirsk, Russia
Keywords: ammonia, carbon-free reaction products, lean and rich mixtures, detonation cell, critical initiation energy
Abstract >>
For the ammonia/hydrogen/oxygen dual-fuel combustion system, stoichiometric, lean, and rich mixtures are analyzed, and the most interesting and important gas-dynamic and kinetic parameters of combustion, explosion, and detonation are presented. From an explosion safety perspective, critical initiation energy data are most important, allowing for an analysis of the relative hazard of various mixtures. Critical energies E* are defined as the minimum energies of the initiator that ensure the propagation of combustion and detonation waves in the mixture under study: the lower the E*, the more hazardous the mixture.
|
|
F. A. Bykovsky1, S. A. Zhdan1,2, E. F. Vedernikov1, A. N. Samsonov1
1Lavrentyev Institute of Hydrodynamics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia 2Kutateladze Institute of Thermal Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
Keywords: continuous spin detonation, continuous pulsating detonation, ammonia, hydrogen, air, transverse detonation waves, vortex radial combustion chamber
Abstract >>
Continuous spin detonation modes of carbon-free ammonia/hydrogen-air fuel-air mixtures have been implemented for the first time in a radial vortex combustion chamber with an outer diameter of 500 mm and an outlet diameter of 125 mm. Single-wave continuous spin detonation modes with a velocity of 1.57-2.33 km/s and a wave rotation frequency of 1.0-1.48 kHz at φ = 0.7-2.03 were achieved in ammonia/hydrogen-air mixtures with fuel of four compositions: NH3 + 8H2, NH3 + 4H2, NH3 + 3H2, and NH3 + 2H2. For the NH3 + 2H2 mixture, continuous pulsating detonation along the combustion chamber radius was also observed at a frequency of approximately 0.15 kHz with an excess fuel ratio of 1.11-1.18. For the NH3 + H2 mixture, conventional subsonic combustion was observed. The detonation velocity relative to the cylindrical surface of the combustion chamber was close to the ideal Chapman-Jouguet velocity. A complex structure of transverse detonation waves and a flow pattern in their vicinity were observed. The region of continuous spin detonation modes was determined depending on the ammonia content in the binary fuel and the pressure in the air manifold. Hot spots were detected in the flow region of the fresh mixture, influencing the formation of a detonation-capable layer.
|
|
T. A. Khmel, S. A. Lavruk
Khristianovich Institute of Theoretical and Applied Mechanics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
Keywords: aluminum gas suspensions, detonation, inert clouds, mathematical modeling, numerical modeling
Abstract >>
Using physical, mathematical, and numerical modeling of one-dimensional and two-dimensional flows, we investigate the conditions for attenuation and suppression of heterogeneous detonation waves of airborne suspensions of finely dispersed aluminum particles by clouds of inert particles. A parametric analysis of the effects of aluminum particle loading, dispersion, and concentration of inert particles is conducted. Criteria for complete detonation failure by semi-infinite clouds are obtained. A quadratic dependence of the critical concentration on the diameter of the inert particles is established. The sizes of inert particle clouds that ensure detonation quenching at supercritical concentrations are determined. It is found that the sizes of short clouds obtained in one- and two-dimensional calculations differ by several times, which is due to the possibility of detonation reinitiation in a transverse wave after leaving the inert particle cloud. Moreover, the results of one- and two-dimensional calculations are equivalent under the condition of quenching by semi-infinite (or sufficiently extended) inert clouds.
|
|
Yu. V. Bogatov, D. Yu. Kovalev, V. A. Shcherbakov
Merzhanov Institute of Structural Macrokinetics and Materials Science, Russian Academy of Sciences, Chernogolovka, Russia
Keywords: mechanical activation, Ti + C, adsorbed oxygen, ignition and combustion temperatures, combustion rate, contact surface
Abstract >>
The effect of mechanical activation of reactants in a ball mill on the synthesis of ceramic materials belonging to the Ti-C system was studied. X-ray diffraction and chemical analysis methods revealed that under conditions of individual mechanical activation (MA) of titanium, oxygen is not incorporated into the crystalline structure of titanium, but segregates on the particle surface. It is shown that the combined MA of titanium and carbon black leads to the formation of a Ti-C composite structure, in which carbon black particles, filling defects on the surface of titanium particles, create a protective barrier suppressing oxygen segregation in the surface layer of titanium. It is shown that the ignition and combustion temperatures increase linearly with increasing oxygen content in the initial titanium, but decrease with increasing MA duration. In contrast, the combustion rate increases with the development of the contact surface during MA and decreases with increasing oxygen concentration in the initial titanium powder. An inverse correlation between the ignition temperature and the combustion rate was established. Mechanical activation has been shown to be an effective tool for controlling the reactivity of Ti + C mixtures, as the barrier effect created by carbon black particles suppresses titanium oxidation and allows for optimization of self-propagating high-temperature synthesis parameters.
|
|
A. E. Kraus1, A. E. Buzyurkin1,2, M. P. Devushkin3, A. O. Kashkarov3,2, E. I. Kraus1, E. R. Pruuel3, K. A. Ten3,2, V. M. Fomin1,2, I. I. Shabalin1
1Khristianovich Institute of Theoretical and Applied Mechanics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia 2Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia 3Lavrentyev Institute of Hydrodynamics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
Keywords: synchrotron radiation, numerical simulation, heterogeneous material, shock waves
Abstract >>
This paper presents a numerical simulation of dynamic loading of polycarbonate and polymethyl methacrylate samples by shock waves, with results verified using synchrotron radiation experiments. The calculations were performed using the «Reactor3D» software package. An algorithm for reconstructing the amount of material in the synchrotron radiation beam was implemented for comparison with the experiment. Experimental data were obtained using high-speed radiography at the VEPP-3 storage rings. A comparison of the calculated and experimental diagrams revealed qualitative agreement between the wave patterns: the slopes of the shock wave fronts and the contact interface in both cases agree within a confidence error of less than 5%.
|
|
A. S. Zolkin1, S. A. Bordzilovsky2, M. S. Voronin2,3, P. V. Geydt1, S. M. Karakhanov2, S. Yu. Chepkasov1
1Novosibirsk State University, Novosibirsk, Russia 2Lavrentyev Institute of Hydrodynamics, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia 3Novosibirsk State Technical University, Novosibirsk, Russia
Keywords: shock wave, temperature, amorphous carbon film, pyrometry, emissivity, carbon film, absorption coefficient
Abstract >>
Experiments were conducted to measure the temperature of a shock-compressed transparent substance by introducing a thin film with high emissivity into the sample. On PMMA samples coated with a carbon film ≈0.3 µm thick, the temperature jumps to a value corresponding to the PMMA temperature in less than 100 ns. However, on quartz samples coated with a carbon film, rapid relaxation of the film temperature to the ambient temperature is not observed. It is hypothesized that this difference may be due to the different heating rates of the film in these cases, as it depends on the ratio of the thermal diffusivities of the film and the sample.
|
|
A. M. Podurets1,2, M. I. Tkachenko1
1All-Russian Scientific Research Institute of Experimental Physics, Sarov, Russia 2Sarov State Physics and Technical Institute Department of the Moscow Engineering Physics Institute, Sarov, Russia
Keywords: shock wave, dislocation density, pulsed X-ray diffraction analysis, molybdenum, aluminum
Abstract >>
The possibility of measuring dislocation density in metals directly during shock wave loading is demonstrated and a method is proposed. Data obtained using pulsed X-ray diffraction analysis are used for this purpose. It is concluded that sample motion must be taken into account during pulsed X-ray diffraction imaging. A computational and experimental method for introducing a correction for sample motion is proposed. Experimental results on dislocation density were obtained for aluminum polycrystals at pressures of 24.5 and 26.5 GPa and molybdenum at 10, 22, and 30 GPa.
|
|
X. Wen1, Y.-C. Liu1, H.-J. Yu2, J.-H. Wang1, J.-Q. Linghu1, N. Zhang2, X.-X. Wang2
1School of Environmental and Safety Engineering, North University of China, Taiyuan, China 2Qingyang Chemical Industry Corporation, Liaoyang, China
Keywords: boron, microspheres, combustion
Abstract >>
Due to the low energy release efficiency of boron, its widespread application as a high energy density material in the defense industry is limited. To address this issue, 50-nm B/Nitrocellulose (NC)/Perfluoroalkoxy polymer (PFA) energetic microspheres were prepared using an emulsion self-assembly method, and a comparative study was conducted with 5-μm and 50-nm boron-based fuels of the same composition prepared via the solvent evaporation method. The results indicate that the three-dimensional network structure constructed by NC, combined with the synergistic effect of the highly fluorinated component PFA, can effectively promote the energy release of boron. The interstitial gaps between microspheres facilitate oxygen permeation and diffusion, enabling a heat of combustion of 23.69 kJ/g. Compared with both 50-nm and 5-μm powdered boron-based fuels, the energetic microspheres exhibit more complete and stable combustion, along with a longer combustion duration.
|
|
K. Wu, J.-G. Ning, Q.-D. Chen, X.-Z. Xu
State Key Laboratory of Explosion Science and Safety Protection, Beijing Institute of Technology, Beijing, China
Keywords: effective charge, shaped charge, charge penetration, velocity distribution
Abstract >>
Classical shaped-charge jet penetration models commonly rely on full-charge or ideal-fluid assumptions and therefore tend to overpredict jet velocity and penetration capability, especially for high-strength metallic targets. To improve the physical consistency between jet formation and penetration, this study develops a hierarchical coupled framework that integrates a dynamic effective-charge model, virtual-origin kinematics, jet-breakup description, and target-strength correction into a quasi-steady penetration formulation. Shock-focusing-based effective-charge partition and a variable-acceleration liner-collapse law are used to derive the axial velocity distribution of jet microelements, allowing the corrected initial velocity field to be transmitted explicitly to the penetration solution. Model inputs are determined from charge geometry, material properties, and ALE-assisted inversion of the virtual origin. Validation is performed at three levels: ALE simulation for kinematic consistency, grid-target experiments for jet-head velocity and perforation behavior, and benchmark penetration cases with reported depth data for quantitative comparison. The results show that the proposed framework provides more physically consistent velocity input and more robust penetration estimates than conventional models under different stand-off conditions.
|
|
L.-L. Yao1, L.-L. Gu2, S.-Y. Wang1, Z. Wang1, Y. He1, Z.-Q. Huang3, Y.-L. Bai1
1School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, China 2School of Safety Science and Engineering, Nanjing University of Science and Technology, Nanjing, China 3Luoyang Institute of Science and Technology, Luoyang, China
Keywords: T-shaped tunnel, propagation characteristics, shock wave, attenuation mechanism
Abstract >>
T-shaped tunnels, as a common structural form in underground engineering, exhibit the shock wave propagation and attenuation patterns within the interiors that significantly influence the protective design of the entire underground structure. This study presented model tests on the propagation characteristics of various explosive charges in the T-shaped tunnel, and revealed the variation patterns of shock wave parameters as the propagation distance increased. Moreover, the finite element model of the T-shaped tunnel was developed. By comparing test data from the T-shaped tunnel with the results of the numerical simulation, the validity of the simulation was verified, and a preliminary analysis of the pressure distribution at the T-junction was conducted. By analyzing the partial pressure coefficients and overpressure parameters of the main and branch channels, this study proposed a modified partial pressure coefficient calculation equation. The partial pressure coefficient within the T-shaped tunnel rose from approximately 0.4 to 0.7 as the branch tunnel distance from the explosion source increased. Under smaller charges, the partial pressure effect toward the branch channel was more pronounced. Longer branch distances could provide a better partial pressure effect. This modified equation overcomes the limitations of previous predictive models, improves prediction accuracy, and provides a theoretical foundation for underground structure protection.
|
|