Results of experimental investigation of regular wave conditions for straight rivulets falling down a vertical plane are presented. Field measurements of the local thickness of rivulets were carried out with the help of laser-induced fluorescence. Data on the wave structure of rivulets is shown in a wide range of frequencies of regular waves for different Reynolds numbers of the flow and contact wetting angles. It was observed for all studied wave conditions that transverse width of rivulets and wetting angles are insensitive to the phase of propagating waves. Moreover, it was found that the wave structure of rivulets differs significantly for the cases of low and high values of the contact angle.
Heat transfer in the laminar-wavy film of liquid falling over the heated plate is studied numerically. To describe the wavy film flow the integral model is applied. Calculation results demonstrate the effect of physical properties of liquid and wavy flow parameters on heat transfer intensification by stationary running waves.
The mathematical model of decomposition of a spherical gas hydrate particle in water behind a 1D wave of the stepped profile (rarefaction wave) is suggested. Contribution of the outer and inner heat flux in a particle to the process of hydrate decomposition is studied. The effect of the gas hydrate particle size, pressure and temperature jumps in liquid on gas hydrate decomposition is investigated.
A physical and mathematical model is developed, and numerical studies are carried out to investigate the processes of non-equilibrium crystallization of a metallic liquid droplet modified with refractory solid nano-inclusions at its impingement on a solid substrate. The conditions are considered, which are typical of thermal spraying of metal coatings, including the plasma spraying. An analysis of the splat formation depending on the concentration of refractory nanoparticles within the metallic droplet volume, their size and substrate temperature is given. The characteristics of splats computed using the non-equilibrium and equilibrium models of crystallization are compared under the same remaining conditions. The conditions of applicability of models are discussed.
Temperature dependences of the density of liquid silver-tin melts containing 61.6 and 96.5 wt. % Sn (59.3 and 96.15 at. % Sn) have been determined using gamma-ray attenuation technique over the temperature range from liquidus line to 950 K. The density changes during solid-liquid transition have been directly measured for the first time for eutectic alloy (96.5 wt. % Sn). The temperature and concentration dependences of the thermal properties for Ag-Sn system have been constructed. Kinetics of homogenization of the melts with mean composition of 61.6 wt. % Sn has been investigated in the temperature range from 770 to 950 K. The coefficients of binary diffusionhave been derived from these experiments.
A wide variety of electric-arc reactors are involved in different areas of science and technologies. Therefore, a demand arose for their systematization. Here we present the classification of most existing types of electric-arc reactors regarding the mutual positioning of plasma-generation and reaction zones. There are three types of reactors: separated, single-chamber, and combined type. Different engineering solutions in each type led to some scatter in the thermal efficiency, power range, lifetime, and other results. No consideration has been given to the reactors of single-chamber heating. They are very special and require individual researches.
The modeling of the formation of the equilibrium arc discharge structure in the axisymmetric formulation was carried out in a wide range of the values of current and radius. The boundary separating the radiation and heat-conducting regimes of discharge combustion was determined from computed data. The influence of energy mechanisms on the structure of the discharge was analysed, and a channel model was proposed for computing its parameters in the radiation regime.
A new quasi-three-dimensional model of the laser welding of thin metal plates and a numerical algorithm of its implementation are proposed. Computations of thermophysical processes at a laser joining of titanium plates are carried out. It is shown that the new model adequately describes thermophysical and hydrodynamic processes occurring in the welding region.
Combustion of a pulverized coal torch has been numerically simulated on the basis of the equations of multicomponent turbulent two-phase flows. The results of three-dimensional simulation of conventional and plasma activated coal combustion in a furnace are presented. Computer code Cinar ICE was verified at coal combustion in the experimental furnace with thermal power of 3 MW that was equipped with plasma-fuel system. Operation of the furnace has been studied at the conventional combustion mode and with plasma activation of coal combustion. Influence of plasma activation of combustion on thermotechnical characteristics of the torch and decrease of carbon loss and nitrogen oxides concentration at the furnace outlet has been revealed.
