Publishing House SB RAS:

Publishing House SB RAS:

Address of the Publishing House SB RAS:
Morskoy pr. 2, 630090 Novosibirsk, Russia



Name:
Authors:
Keywords:
Abstract:
   

Thermophysics and Aeromechanics

2024

Number: 1

6041.
Comparison of air temperature at the level of the inner wall of vortex tubes with circular and square cross sections of the working channel

M.R. Gordienko, I.K. Kabardin, M.Kh. Pravdina, S.V. Kakaulin, V.I. Polyakova, V.G. Meledin, G.V. Bakakin, N.I. Yavorsky
Kutateladze Institute of Thermophysics SB RAS, Novosibirsk, Russia
Keywords: vortex tube, Ranque tube, wall temperature, flow crisis

Abstract >>
The gas temperature measurements at the level of the inner wall of Ranque vortex tubes of the square and circular cross sections with variations in the cold mass fractions for both tubes showed the presence of three characteristic zones of temperature growth, which do not change over a wide range of the cold mass fraction. These zones are typical when analyzing the flow in a vortex tube within the framework of the flow crisis concept.



Number: 1

6042.
A source of controlled nonstationary harmonic flow disturbances

T.A. Gimon, D.A. Elistratov, A.D. Zhelonkin, S.V. Lukashevich, S.O. Morozov, A.N. Shiplyuk
Khristianovich Institute of Theoretical and Applied Mechanics SB RAS, Novosibirsk, Russia
Keywords: laminar boundary layer, nonstationary harmonic disturbances of the flow, source of controlled disturbances, Görtler instability

Abstract >>
The flow in the vicinity of the source of controlled harmonic non-stationary perturbations of a gas medium, applicable for generating Görtler vortices in a compressible boundary layer, is studied. The source has a flat surface with linearly arranged cylindrical channels, leading alternately to two cavities of variable volume. Various configurations of the source are considered: with separate channel outlet openings and with a slit opening above them. Numerical simulation is performed in the Solid Works Flow Simulation package, and experimental measurement of gas velocity is realized by the PIV method. The developed source is shown to create periodic velocity fluctuations with an amplitude of up to 2 m/s at a frequency of 1 kHz near the surface. The shapes of the profiles of velocity normal to the surface along the source are close to sinusoidal in both time and space.



Number: 1

6043.
Application of optical visualization of the inner surface temperature of a thin-walled model in the flow in a hotshot wind tunnel

I.S. Tsyryulnikov, T.A. Korotaeva, Yu.V. Gromyko, N.A. Maslov
Khristianovich Institute of Theoretical and Applied Mechanics SB RAS, Novosibirsk, Russia
Keywords: hotshot wind tunnels, temperature measurements, fluorescent coatings, temperature-sensitive coatings, numerical simulation, surface temperature visualization

Abstract >>
A method of panoramic temperature measurement based on registering the fluorescence of thin-walled coatings on the inner surface of a flying vehicle model is considered. The method allows investigations in optically polluted flows of high-enthalpy short-duration wind tunnels. The temperature and heat fluxes on the aerodynamic model surface are retrieved by means of combining the results of temperature measurements with the numerical solution of an adjoint problem of the flow around the flying vehicle. Implementation of this method in practice is performed in the flow of a hotshot wind tunnel based at ITAM SB RAS.



Number: 1

6044.
Effect of the type of thermal boundary conditions on heat transfer and skin-friction in a convergent channel

A.Yu. Sakhnov, K.V. Bryzgalov, V.S. Naumkin, K.S. Lebeda
Kutateladze Institute of Thermophysics SB RAS, Novosibirsk, Russia
Keywords: boundary layer, heat transfer, laminarization, velocity overshoot, numerical modeling, favorable pressure gradient

Abstract >>
Investigation results on the air flow in a convergent channel with a hot bottom wall at a set constant heat flux or a set constant wall temperature are presented. The numerical simulation was carried out in the OpenFOAM software using the k-ω- SST turbulence model. The verification of simulation results demonstrated a good agreement between the calculated data and the experimental velocity profiles and the thermal Stanton number. The study showed that an increase in the temperature of the convergent channel wall leads to the phenomenon of the streamwise velocity overshoot, suppression of turbulence and a decrease in the skin-friction coefficient and thermal Stanton number. In contrast to a zero pressure gradient flow, the type of thermal boundary conditions has a noticeable effect on the skin-friction and heat transfer in the convergent channel.



Number: 1

6045.
Numerical study of the reverse flow behind the Mach disk in an underexpanded supersonic jet

A.V. Kashkovsky, A.N. Kudryavtsev, A.A. Shershnev
Khristianovich Institute of Theoretical and Applied Mechanics SB RAS, Novosibirsk, Russia
Keywords: supersonic nonisobaric jets, shock wave structure, axisymmetric flow, rarefied gas, Direct Simulation Monte Carlo method

Abstract >>
Numerical simulations of an underexpanded supersonic jet exhausting from a circular nozzle are reported. The study is performed in a three-dimensional formulation using two different approaches: Navier-Stokes equations and Direct Simulation Monte Carlo method. In both cases, a reverse flow zone is formed behind the Mach disk in the first shock cell. Thus, this phenomenon, which was previously observed in axisymmetric simulations, cannot be attributed to inaccuracies of approximation of these equations near the axis of symmetry.



Number: 1

6046.
Numerical simulation of internal flows with three-dimensional swept interaction of shock waves

I.I. Mazhul, Yu.P. Gounko
Khristianovich Institute of Theoretical and Applied Mechanics SB RAS, Novosibirsk, Russia
Keywords: supersonic flows, channel with a square cross section, compression wedges, three-dimensional interaction of shock waves

Abstract >>
Results of a numerical study of supersonic flows formed in channels with a square cross section are reported. Configurations consisting of a constricting entrance section formed by four compression wedges aligned at a right angle to each other and a subsequent channel with a constant cross section are considered. The initial shock waves formed on the nose compression wedges pairwise intersect each other in dihedral corners of the configuration along the swept lines, and a complex system of reflected and subsequent interacting shock waves of the general three-dimensional position is formed further downstream. The data are obtained in a supersonic range of freestream Mach numbers М = 2 - 4 for compression wedge angles of 3° and 8° in flows with both regular and irregular interaction of the initial shock waves in dihedral corners of the configuration.



Number: 1

6047.
Experimental study of the turbulent flow of an underexpanded jet

A.V. Sobolev
Khristianovich Institute of Theoretical and Applied Mechanics SB RAS, Novosibirsk, Russia
Keywords: underexpanded jet, hanging shock wave, mixing layer, total-pressure sensor, longitudinal velocity disturbances, turbulence intensity

Abstract >>
Measurements of full pressure pulsations in the mixing layer of a supersonic, strongly underexposed jet were performed. The resulting pressure was converted into a longitudinal velocity, which allowed determining the main characteristics of the layer: its growth rate and thickness, longitudinal and transverse dimensions of disturbances, intensity, and spectral composition of turbulence. The layer under consideration was in a state of saturation, with a wide range of disturbances being realized within. The measured growth rate of the layer turned out to be four times higher than that calculated by a statistically generalized method. The intensity of disturbances of the longitudinal velocity component was determined in the considered layer by two groups of disturbances - low-frequency and high-frequency - with approximately equal inputs. From the analysis of the measurement results, it follows that the mass transfer across the layer is inversely proportional to the lengths of the vortices, and in the upper part of the frequency range of intense disturbances it is many times higher. This indicates that intensive mixing generates rapid growth rate of the layer.



Number: 1

6048.
Peculiarities of reducing the broadband transfer of vibration and working medium pulsation through vibration-isolating junctions of pipelines with liquid by constructive and active methods

A.V. Kiryukhin1,2, O.O. Milman1,2, A.V. Ptakhin1,2, V.O. Miloserdov1,2
1Tsiolkovsky Kaluga State University, Kaluga, Russia
2SPC Turbocon, Kaluga, Russia
Keywords: vibration frequency, pipeline vibration-isolating junctions, vibration rigidity, vibration force, pressure pulsation, active antivibration system, shock absorber, force sensor, transfer function, amplification factor, feedback, direct connection

Abstract >>
It is shown that the vibration transfer and working medium pressure pulsations through vibration-isolating pipeline junctions of various plants may increase by two or three orders of magnitude with an increase in the vibration frequency and in the presence of incompressible working fluid. The results of research of the found physical models that determine this phenomenon are presented. The experimental results for a spatial three-component broadband active vibration-protection system (AVS) for vibration damping beyond the vibration isolation junction with liquid are considered. An experimental plant scheme for studying the simultaneous spatial active damping of dynamic forces, vibrations and pressure pulsations downstream from the junction has been given. Calculated dependences of the maximum efficiency of considered AVS on frequency are obtained. Efficient active damping of forces is shown to be attainable in an open loop without feedback. While damping in an open loop at the experimental plant, the efficiency of active damping of dynamic forces is obtained in three directions up to 10 dB or more in the frequency range from 5 to 800 Hz (more than seven octaves). The analysis of scientific publications reveals the uniqueness of this result. In this case, there are no zones of negative efficiency outside the active damping frequency range, which appear while using other methods of active damping.



Number: 1

6049.
Determining the amplitude-frequency characteristics of the thermoanemometer + sensor system by laser pulse

D.A. Bountin, O.I. Vishnyakov, P.A. Polivanov, A.A. Sidorenko, Yu.V. Gromyko
Khristianovich Institute of Theoretical and Applied Mechanics SB RAS, Novosibirsk, Russia
Keywords: frequency response, hot-wire, thin-film sensor

Abstract >>
An experimental method is proposed for determining the frequency response of a hot-wire and hot-film system using short-pulse laser action on a sensor. The possibility to obtain frequency response by this method is demonstrated. The frequency response is obtained from constant temperature anemometers of two manufacturers with two types of sensors: surface thin-film and wire.



Number: 1

6050.
Heat transfer control at impinging pulsed gas-drop flow in the regime of evaporative cooling

V.I. Terekhov, P.N. Karpov, A.F. Serov
Kutateladze Institute of Thermophysics SB RAS, Novosibirsk , Russia
Keywords: pulsed multi-nozzle spray, evaporative cooling, pulse duration and frequency, heat transfer, co-current air flow

Abstract >>
The experimental results on heat transfer when a pulsed multi-nozzle spray flows onto a vertical surface are presented. The behavior of the effective heat transfer coefficient averaged over time and over the entire heat transfer surface has been studied. The experiments were carried out in the regime of evaporative cooling at a constant temperature of the heat transfer surface Tw = 70°C. The duration of pulses for supplying the liquid phase of the spray τ and their repetition frequency F were varied in the experiments within wide limits: τ = 1 ÷10 мс and F = 0,25 ÷ 50 Hz. In addition, the effect of droplet phase flow rate on heat transfer was studied by changing the pressure in front of the nozzles (ΔPL = 0,05 ÷ 0,6 MPa). Preliminary studies have shown that heat transfer during spray impingement onto a surface can be strongly influenced by the co-supply of air due to turbulization of the wall layer and the return of droplets reflected from the surface. It has been established that the main factor determining the intensity of heat transfer when the spray flows onto the surface is the time-averaged mass velocity of the liquid phase. Using this value, generalization of experimental data on the heat transfer coefficient and the thermal efficiency parameter of a pulsed spray was achieved.




Articles 6041 - 6050 of 31229
First | Prev. | 603 604 605 606 607 | Next | Last | All